In this work, a flame-retardant polypropylene(PP)/ramie fiber(RF) composite was prepared. The ramie fibers were wrapped chemically by a phosphorus- and nitrogen-containing flame retardant(FR) produced via in situ condensation reaction so as to suppress their candlewick effect. Fourier transform infrared spectroscopy(FTIR), X-ray photoelectron spectroscopy(XPS) and scanning electron microscopy(SEM) demonstrated that the ramie fibers wrapped chemically by FR(FR-RF) were obtained successfully. Thermogravimatric test showed that the PP/FR-RF composite had more residue and better thermal stability at high temperatures than the PP/RF composite. Cone calorimeter(CC) results indicated that the peak of heat release rate(PHRR) and total heat release(THR) correspondingly decreased by 23.4% and 12.5% compared with the values of neat PP/RF. The PP/FR-RF composite created a continuous and compact char layer after the combustion. Combining FTIR analysis of char residue after CC test with heat conduction coefficient results, it could be concluded that the charring of FR on RF greatly weakened the candlewick effect of RF, and more char residue in the RF domain facilitated the formation of more continuous and compact char layer in the whole combustion zone, consequently protected PP composites during combustion, resulting in the better flame retardancy of PP/FR-RF composite than that of PP/RF composite.
Aluminum hypophosphite (AP) was used to prepare flame-retarded thermoplastic polyurethane (FR-TPU) composites, and their flame retardancy, thermal degradation and mechanical properties were investigated by limiting oxygen index (LOI), vertical burning test (UL-94), thermogravimetric analysis (TGA), cone calorimeter (CC) test, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and tensile test. TPU containing 30 wt% of AP could reach a V-0 rating in the UL-94 test, and its LOI value was 30.2. TGA tests revealed that AP enhanced the formation of residual chars at high temperatures, and slightly affected the thermal stability of TPU at high temperatures. The combustion tests indicated that AP affected the burning behavior of TPU. The peak of heat release rate (PHRR), total heat release (THR) and mass loss rate (MLR) greatly reduced due to the incorporation of AP. The tensile test results showed that both the tensile strength and the elongation at break slightly decreased with the addition of AP. The digital photos and SEM micrographs vitrified that AP facilitated the formation of more compact intumescent char layer. Based on these results mentioned above, the flame-retarding mechanism of AP was discussed. Both the self-charring during the decomposing process of AP and its facilitation to the charring of TPU led to the great improvement in the flame retardancy of TPU.
To improve the flame-retardant efficiency and water resistance of ammonium polyphosphate(APP), the UV-curable pentaerythritol triacrylate(PETA) was used to microencapsulate APP via the UV curing polymerization method. The prepared PETA-microencapsulated APP(PETA-APP) was characterized by Fourier transform infrared spectroscopy(FTIR), scanning electron microscopy(SEM), and thermogravimetric(TG) analysis. PETA-APP was used as intumescent flame retardant(IFR) alone to flame retard polypropylene(PP). The water resistance of PP/PETA-APP composites was investigated, and the effect of PETA on the combustion behaviors of PP/APP composites was studied through limiting oxygen index(LOI), vertical burning test(UL-94) and cone calorimeter(CC) test, respectively. With 40 wt% of PETA-APP, the PP/PETA-APP system could achieve a LOI value of 30.0% and UL-94 V-0 rating after treatment in hot water for 168 h, while the LOI value of the system containing 40 wt% uncoated APP was only 19.2%, and it failed to pass the UL-94 rating. CC test results showed that the heat release rate(HRR), mass loss rate(MLR) and smoke production rate(SPR) of PP/PETAAPP system decreased significantly compared with PP/APP system, especially the peak of HRR was decreased by 51.4%. The mechanism for the improvement of flame reatardancy for PP/PETA-APP composites was discussed based on FTIR and X-ray photoelectron spectroscopy(XPS) tests. All these results illustrated that simultaneous improvement of flame retardancy and water resistance for PP/APP was achieved through coating UV-curable PETA onto APP.