The surface composition of poly(3-hexylthiophene-2,5-diyl) and fullerene derivative [6,6]-phenyl-C61-butyric acid methyl ester (P3HT/PCBM) blend films could be changed by controlling the film formation process via using mixed solvents with different evaporation rates. The second solvent, with a higher boiling point than that of the first solvent and much better solubility for PCBM than P3HT, is chosen to mix with the first solvent with a lower boiling point and good solubility for both PCBM and P3HT. The slow evaporation rate of the second solvent provides enough time for PCBM to diffuse upwards during the solvent evaporation. Thus, the weight ratio of PCBM and P3HT (mPCBM/mP3HT) at surface of the blend films was varied from ca. 0.1 to ca. 0.72, i.e., it increases about seven times by changing from single solvent to mixed solvents. Meanwhile, the mixed solvents were in favor to form P3HT naonofiber network and enhance phase separation of P3HT/PCBM blend films. As a result, the power conversion efficiency of the device from mixed solvents with slow evaporation process was about 1.5 times of the one from single solvents.
The preparation of the poly(3-hexylthiophene) (P3HT) stripe structure with oriented nanofibrils prepared by controlled inclining evaporative technique is reported. The distance of the adjacent stripes could be controlled from 40 μm to 100 μm by decreasing the inclining angle. The oriented nanofibrils in the stripes can be obtained because the P3HT lamellae diffuse directionally and form 1D crystals at the three-phase contact line of the drop. In order to get the oriented P3HT stripes, the proper solvent evaporation rate which is controlled by the inclining angle and the wettability of the substrate must be carefully chosen to match the P3HT 1D crystallization rate. It is found that large inclining angle and the hydrophilic substrate (for example: glass and PEDOT) are beneficial to get P3HT stripe structure with oriented nanofibrils.
The preparation of large area coverage of films with uniaxially aligned poly(3-hexylthiophene)(P3HT) nanofibers by using zone-casting approach is reported.The length and the orientation of the nanofibers are defined by the solubility of the solvent,the P3HT molecular weight and the substrate temperature.The length of the oriented nanofibers could be increased from 1 μm to more than 10 μm by adding poor solvent into the P3HT solution.It is found that for P3HT of relatively low molecular weight,a solvent with relatively low solubility has to be chosen to get the oriented film.While for the high molecular weight P3HT,the solvent with a relatively high solubility has to be used.The well-aligned film could be obtained because of the solute concentration gradient in the region where the critical concentration is reached during the zone-casting process.Particularly,the solvent evaporation rate and crystallization rate must be chosen properly to satisfy the stationary conditions above,which were controlled by an appropriate choice of solvent and substrate temperature.The film prepared by zone-casting approach had microcrystalline P3HT domains with more inter-chain order than spin-coating film.Meanwhile,the P3HT π-π stacking direction was parallel to the alignment direction of the nanofibers.
We report on the effects of aggregation of P3HT with ordered conformation in solution on improving the uniaxial alignment of the P3HT nanofibers by zone casting.Two approaches were employed to change the aggregation of P3HT:P3HT blending with coil insulating polymer and ultrasonic oscillating.The insulator polymer(i.e.PS) which has good solubility in the solution would disturb the aggregation of P3HT to prevent the chains entanglement.The ultrasonic oscillation can further improve the P3HT aggregation with ordered conformation in the solution.As a result,the P3HT nanofibers in the film grew much orientedly by zone casting the ultrasonic oscillating P3HT/PS polymer blends solution than the same solvent P3HT solution without ultrasonic oscillating and blending.The P3HT tt-tt stacking direction is parallel to the alignment direction of the nanofibers.Meanwhile,the P3HT/PS blend ratio and PS molecular weight have influence on the uniaxial alignment of P3HT nanofibers.Only P3HT/PS is 1:1, the P3HT nanofibers oriented well.The low molecular weight PS can make the P3HT nanofibers orient better than that of the high molecular weight.
Xiang GaoJian-Gang LiuYue SunRu-Bo XingYan-Chun Han
